Errorcodes E800 To E850 for Canon ImageRunner 7105/7095/7086

 

 

E800 The auto power-off circuit has an error.An open circuit has been detected for 3 sec or more in the auto power-off circuit.

Turn off and then on the power. Disconnect and then connect J505 of the DC controller PCB.Disconnect and then connect J1719 of the relay PCB. Replace the relay PCB. Replace the DC controller PCB.

E804 The rotation of the following is faulty: power supply cooling fan 1,
power supply cooling fan 2, controller cooling fan.
0001 The fan stop signal has been detected for 5 sec or more after the power supply
          cooling fan 1 has gone on.

Disconnect and then connect J505 of the DC controller PCB.Replace the power supply cooling fan 1. Replace the DC controller PCB.

0002 The fan stop signal has been detected for 5 sec or more after the power supply cooling fan 2 has gone on.

Disconnect and then connect J505 of the DC controller PCB.Replace the power supply cooling fan 2. Replace the DC controller PCB.

0004 The fan stop signal of the controller cooling fan has been detected continuously for 16 sec.

Disconnect and then connect J1028 of the main controller
PCB. Replace the controller cooling fan. Replace the main controller PCB.
E805 The fixing heat discharge fan rotation is faulty.

0002 The fan stop signal has been detected for 5 sec or more after the fixing heat
discharge fan has gone on.

Disconnect and then connect J503 of the DC controller PCB.
Replace the fixing heat discharge fan. Replace the DC controller PCB.
E820 The drum fan rotation is faulty.

0000 The fan stop signal has been detected for 5 sec or more after the drum fan has gone on.
Disconnect and then connect J512 of the DC controller PCB.

Replace the drum fan. Replace the DC controller PCB.
E823 The pre-transfer charging assembly fan rotation is faulty.

0000 The fan stop signal has been detected for 5 sec or more after the pre-transfer
charging assembly fan has gone on.

Disconnect and then connect J504 of the DC controller PCB.
Replace the pre-transfer charging assembly fan. Replace the DC controller PCB.
E840 An HP detection error has occurred in relation to the fixing inlet sensor
(fixing wrap jam detection).
0000 The home position is not detected when he sensor is moved up/down (i.e., the sensor has not gone on).
0001 The home position is not detected when the sensor is moved up/down (i.e., the sensor has not gone off).

Disconnect and then connect J508, J552, and J553 of the DC controller PCB. Disconnect
and then connect J4001 and J4002 of the fixing inlet sensor ascent/descent motor driver
PCB; as necessary, replace the fixing inlet sensor ascent/descent motor. Replace the fixing
inlet sensor ascent/descent motor driver PCB.
E850 There is a fault in the double-feeding detection unit.
0000 The double-feeding sensor (reception) fails to attain an ultrasonic signal of a specific level.

Remove paper lint form the surface of the double-feeding sensor (reception). Remount the double-feeding sensor (transmission, reception). Disconnect and then connect J509 and J550 of the DC controller PCB. Replace the double-feeding sensor (transmission, reception). Replace the double-feeding sensor PCB (transmission,reception).

Thousands of Parts and Free Shipping

 

Errorcodes E711 To E749 for Canon ImageRunner 7105/7095/7086

E711 An error has occurred in the communication between the pickup/delivery accessory and the printer unit.
0001 The communication controller has detected a fault.

Turn off and then back on the power. (Turn off the machine and its delivery accessories; then, turn back on all accessories and then the machine.)
Connect the communication cables and terminals between the machine and the delivery accessories once again.
Replace the accessories controller PCB. Replace the transceiver PCB.
E712 An error exists in the communication between the ADF and the reader unit .
0001 As much as 5 sec or more has passed without recovery after communicationstopped
between the reader controller and the ADF controller.

Disconnect and then connect the connectors between the reader unit and the ADF. Replace
the reader controller PCB. Replace the ADF controller PCB.
E717 An error exists in the communication with the NE controller.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0001 The NE controller that has been connected before power-off is not recognized at power-on.
0002 In the communication with the coin vendor, an error that cannot be reset has occurred (e.g.,cable break).

Disconnect and then connect the main controller PCB. Install the NE controller. Replace the NE controller.
E719 An error has occurred in the communication with the coin vendor/card reader.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0001 The coin vendor that was connected before power-off is not recognized at power-on.
0002 In the communication with the coin vendor, an error that cannot be reset has occurred (e.g., cable break).
0003 In the communication with the coin vendor, a communication error has occurred during acquisition of unit price information.

Disconnect and then connect the connector of the main controller PCB. Install the coin vendor.
Replace the coin vendor.

0011 The card reader that was connected before power-off is not recognized at power-on.
0012 In the communication with the card reader, an error that cannot be reset has occurred (e.g., cable break).
Disconnect and then connect the connector of the main
controller PCB. Install the card reader.Replace the card reader.
E730 A PDL-related error has occurred.
1001 An initialization error has occurred at the start of a job.
100A An error has occurred in the communication with an external controller.
Reset the PDL mechanism. Turn off and then on the power.

9004 A fault has been detected in the cable connection with an external controller.
9005 A fault has been detected in the cable connection with an external controller.
Turn off and then on the power. Replace the external
controller relay PCB. Replace the external controller.

A006 The PDL mechanism does not respond. Reset the PDL mechanism.
Turn off and then on the power. Reinstall the system software. Replace the main controller.

A007 At start-up, the version of the machine control software and that of the PDL control software do not match.
Reset the PDL mechanism. Turn off and then on the power. Execute full formatting of the
HDD, and reinstall the system software.

B013 The font data is corrupted at start-up.
Turn off and then on the power. Reinstall the system software. Execute full formatting of
the HDD, and reinstall the system software.

E732 An error has occurred in the communication between the reader unit and the main controller.
0001 An error has occurred in the communication between the reader unit and the main controller.
0010 A fault has been detected in the reader sync signal detection mechanism.
Disconnect and connect the connectors of the read communication cable. Check the
power supply of the reader unit (to see if initialization occurs at power-on). Replace the
reader controller PCB. Reap the reader I/F PCB. Replace the main controller PCB.

E733 An error has occurred in the communication between the reader unit and the main controller.
0000 An error has occurred in the communication between the reader unit and the main controller.
0001 An attempt to communicate with the DC controller fails.
0010 A fault has occurred in the printer engine sync signal detection mechanism.
Disconnect and then connect the connector. Check the power supply of the DC controller (to
see if initialization occurs at time of start-up). Replace the DC controller PCB. Replace the
main controller PCB.

E740 An error exists in the LAN controller .
0002 An illegal MAC address has been detected at start-up.
Replace the main controller PCB.

E743 A fault exists in the communication between the main controller and the reader controller.
0000 The reader controller has detected an error in the communication between the main controller and the reader controller.
Disconnect and then connect the connectors of the reader
communications cable. Replace the reader controller PCB. Replace the main controller PCB.

E744 An error exists in the language file/boot ROM.
0001 The version of the language file on the HDD and that of bootable do not match.
0002 The language file on the HDD is too large.
0003 There is no language to which a switchover is made as described in the Config file on the HDD.
0004 An attempt to switch over to the language described in the Config file on the HDD fails.
Update the version of the language file (Language), or install the appropriate file.

1000 The connected boot ROM is not one designed for the model in question.
Replace the boot ROM.

2000 An illegal engine ID has been detected.
Reinstall the system software.

E746 An unsupported optional board has been detected.
0003 The option board that has been detected is one deigned for a different model.
Replace it with one for the model in question.

E749 Restart in accordance with a change of the product configuration .
0001 A boot ROM designed for a different model has been fitted in place (as when installing an PDL option).
There is no need for remedial action. Nevertheless, the fact
will remain as part of the
error history.

Thousands of Parts and Free Shipping

 

Errorcodes E302 To E610 For ImageRunner 7105/7095/7086

 

 

E302 Shading operation is faulty.

0000 In the course of shading operation, the processing doses not end within thereader controller.
Disconnect and then connect J1107 and J1108 of the reader controller PCB.
Replace the reader controller PCB.
E315 The image data codec has a fault.
0007 A JBIG encoder error has occurred.
Replace the main controller PCB.
000d A JBIG decoding error has occurred .
000e An error has occurred in the course of software decoding .
Replace the DDR-SDRAM. Replace the HDD.Replace the main controller PCB
0100 An overrun error has occurred
Replace the main controller PCB.
0200 the open I/F relay PCB has detected an error (no recovery after a retry).
Replace the open I/F relay PCB (relay PCB between the main controller and PS controller).
0300 Cubic time-out Turn off and then back on he power. .
0400 Shift Device A time-out.
0401 Shift Device B time-out
Replace the main controller PCB
E351 An error has occurred in the main controller communication.
0000 At start-up, a main controller communication error has occurred.
Replace the main controller PCB.
E400 ** An ADF communication error has occurred.0001 A check sum error has occurred. Disconnect and then connect the connector. 0002 A reception status error has occurred.
0003 A reception interrupt error has occurred.
Replace the reader controller PCB. Replace the ADF controller PCB.
E402 * The ADF belt motor rotation is faulty .
0000 While the belt motor drive signal is on, no lock signal occurs for 100 msec.
Disconnect and then connect the cable between the belt motor driver PCB and the ADF controller PCB.
Replace the belt motor clock sensor. Replace the belt motor clock sensor.
Replace the belt motor. Replace the belt motor driver PCB.Replace the ADF controller PCB.
E404 * The ADF delivery motor rotation is faulty .
0000 When the delivery motor drive signal is on, no clock signal occurs for 200 msec.
Replace the delivery motor. Replace the delivery motor clock sensor. Replace the ADF controller PCB.
E405 * The ADF separation motor rotation is faulty .
0000 When the separation motor drive signal is on, no clock signal occurs for 200 msec.
Replace the separation motor. Replace the separation motor clock sensor. Replace the ADF controller PCB.
E410 * The ADF pickup motor rotation is faulty .
0000 No signal occurs from the following sensors within 2 sec after the pickup motor is driven:
- pickup roller height sensor 1 (PI8), pickup roller height sensor 2 (PI9)
- pickup roller HP sensor (PI7)
Replace the pickup motor. Replace the pickup roller height sensor (PI8). Replace the pickup
roller height sensor 2 (PI9). Replace the pickup roller HP sensor (PI7). Replace the ADF controller PCB.
E413 ** The ADF shift motor rotation is faulty .
0001 The shift motor HP sensor is open. 0002 Shift motor HP sensor is closed.
Disconnect and then connect the connector. Replace the shift motor HP sensor. Replace the shift motor.
E420 * An ADF EEPROM read error has occurred .
0000 At power-on, an attempt to read the EEPROM backup data fails. Or, data that has been read has a fault.
Replace the ADF controller PCB.
E490 The ADF is of the wrong type.
0001 The ADF is of the wrong type.
Replace the ADF.
E602 The HDD has an error.
E604 The time memory (DDR-SDRAM) is faulty or inadequate.
0000 A DDR-SDRAM (1 GB) of adequate capacity is not detected.
Replace the DDR-SDRAM.
E609 The HDD temperature is abnormally low.
0008 At start-up, the HDD does not reach a specific temperature within a specific time.Replace the HDD.
0009 When returning from sleep mode, the HDD does not reach a specific temperature within a specific time.
Replace the HDD.
E610 The HDD encryption key is faulty.
0001 The memory is missing.Install the security board.
0002 The memory is inadequate.
Replace the DDR-SDRAM with one for the model in question (1 GB).
0101 An attempt to initialize the key storage area of the memory has failed. Turn off and then on the power.
Replace the main controller PCB.
0102 An error has occurred while the encryption processing area is being initialized.
Turn off and then on the power. Replace the security board.
0201 An error has occurred in the encryption processing area.
0202 An error has occurred in the encryption processing area.
0301 An attempt to create an encryption key has failed.
Turn off and then on the power. Replace the security board.
0302 A fault exists in the encryption key. .
0303 A fault exists in the encryption key. PCB.
Turn off and then on the power. Replace the main controller PCB.
0401 An error has been detected during coding. Turn off and then on the power .
0402 A fault has been detected in decoding.
0501 An error exists in the file management information in the image storage area.

Turn off and then on the power. Replace the security board.

Thousands of Parts and Free Shipping

 

Errorcodes E111 To E251 For Canon ImageRunner 7105/7095/7086

 

E111 The laser scanner motor cooling fan rotation has a fault.
0000 After the laser scanner motor cooling fan has gone on, the fan stop signal is detected for 5 sec or more.

Disconnect and then connect J503 of the DC controller PCB.Replace the laser scanner motor cooling fan. Replace the DC controller PCB.
E121 A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat discharge fan 1, reader heat discharge fan 2.
0001 The laser scanner unit cooling fan has a fault.
After the laser scanner unit cooling fan has gone on, the fan stop signal isdetected for 5 sec or more.

Disconnect and then connect J503 of the DC controller PCB.
Replace the laser scanner unit cooling fan. Replace the DC controller PCB.
0002 The reader heat discharge fan 1 has a fault.After the reader heat discharge fan 1 has gone on, the fan stop signal isdetected for 5 sec or more.

Connect and then disconnect J512 of the DC controller PCB.
Replace the reader heat discharge fan 1. Replace the DC controller PCB.
0003 The reader heat discharge fan 2 has a fault.After the reader heat discharge fan 2 has gone on, the fan stop signal isdetected for 5 sec or more.

Disconnect and then connect J521 of the DC controller PCB.
Replace the reader heat discharge fan 2. Replace the DC controller PCB.
E197 The laser scanner motor communication has a fault.

0000 The communication with the laser control IC is not normal.
Replace the laser scanner unit. Replace the video PCB.
E202 The scanner HP detection mechanism has a fault.
0001 While HP positioning is under way, the forward trip fails.
Disconnect and then connect the connector of the scanner HPsensor. Replace the scanner HP sensor. Replace the scanner motor. Replace the readercontroller PCB.
0002 While HP positioning is under way, the reverse trip fails.
Disconnect and then connect the connector of the scanner HPsensor. Replace the scanner HP sensor. Replace the scanner motor. Replace the readercontroller PCB.
E225 The intensity of the scanning lamp is inadequate. (The lamp is exhausted.)
0001 At time of shading, the intensity of light is below the standard level.

Disconnect and then connect the connector of the scanning lamp.
Replace the scanning lamp. Replace the inverter PCB. Replace the reader controller PCB.
** 0002 In ADF mode, the intensity of light is below the standard level between sheets.
E227 The reader unit power supply (24 V) has a fault.
0001 At power-on, the 24V port is off.
0002 At the start of a job, the 24V port is off. connector. .
0003 At the end of a job, the 24V port is off.
0004 While a load is driven, the 24V port is off.

Disconnect and then connect the reader power supply
Replace the power supply
E240 A fault exists in the communication between the main controller and the DC controller.
0000 A fault has occurred in the communication between the CPUs of the main controller and the DC controller.

Disconnect and then connect the connector.
Replace the DCcontroller PCB. Replace the main controller PCB.
E248 A fault exists in the following: main controller SRAM, reader controller EEPROM.
0000 At start-up, an SRAM check error has occurred..
0001 An error has occurred at time of power-on (EEPROM). .
0002 An error has occurred during write operation (EEPROM).
0003 A read error has occurred after write operation (EEPROM).

Replace the main controller PCB.Replace the reader controller PCB
E251 The inverter cooling fan rotation is faulty.
0000 After the inverter cooling fan has gone on, the fan stop signal is detected for 5 sec or more.
Disconnect and then connect J1110 of the reader controller PCB.
Replace the inverter cooling fan. Replace the reader controller PCB.

Thousands of Parts and Free Shipping

 

Errorcodes E025 To E069 and Solution for Canon ImageRunner IR7105/7095/7086

 

E025 The toner bottle motor rotation is faulty.
0000 A toner bottle motor error (over-current) is detected for 10 sec for a second time.
MEMO:
The 1st detection of the error will cause the machine to indicate the message.
"Shake and Replace the Toner Container."
Disconnect and then connect J512 of the DC controller PCB.
0001 The toner bottle motor is not connected.
MEMO:
The 1st detection of the error will cause the machine to indicate the message.
"Shake and Replace the Toner Container."
Disconnect and then connect J512 of the DC controller PCB.
E032 The copy data controller/NE controller counter fails to operate. 
0001 An open circuit of the counter signal has been detected.

Disconnect and then connect J1022 of the main controller PCB.
Replace the copy data controller/NE controller.
Replace the main controller PCB.
E043 The rotation of the pickup motor of the side paper deck is faulty. 
0000 The side paper deck pickup motor has gone on, but the PLL lock signal is not
detected for 2 sec or more (1st detection).
MEMO:
For the 2nd and subsequent detection, the machine will indicate "E043" on the
screen offering a choice of sources of paper.

Disconnect and then connect J101 and J106 of the side paper deck driver PCB.
Replace the pickup motor.Replace the side paper deck driver PCB.
Replace the DC controller PCB.
E051 The horizontal registration HP detection has an error. 
0001 After the start of horizontal registration HP detection, the HP sensor is not off
within 5 sec (i.e., not leaving home position).
MEMO:
If an error is detected in the course of horizontal registration HP detection at
power-on, the machine will indicate the presence of a jam.

Replace the horizontal registration HP sensor.Replace the horizontal registration motor.
Replace the stackless transport driver PCB.Replace the DC controller PCB.
0002 After the start of horizontal registration HP detection, the home position is not detected within 5 sec.
MEMO:
If an error is detected in the course of horizontal registration HP detection at
power-on, the machine will indicate the presence of a jam.
Replace the horizontal registration HP sensor.Replace the horizontal registration motor.
Replace the stackless transport driver PCB.
Replace the DC controller PCB.
0003 At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec.

Replace the horizontal registration HP sensor.Replace the horizontal registration motor.
Replace the stackless transport driver PCB.Replace the DC controller PCB.

E065 The high-voltage output has a fault. (primary charging assembly)
0000 A fault (leak) is detected when high voltage is supplied to the primary charging assembly.

Remove and then mount the primary charging assembly.Check for soiling.
Disconnect and then connect T601, J723, and J731 of the HV-DC PCB.
Replace the HV-DC PCB.
E067 The high-voltage output has a fault.
0000 A fault is detected at the same time in 2 of the following: primary high voltage, pre-transfer
high voltage, transfer high voltage, separation high voltage.

Remove and mount the primary charging assembly.
Remove and mount the pre-transfer charging assembly.
Remove and mount the transfer/ separation charging assembly.
Disconnect and then connect J721, J723, J731, and J734 of the HV-DC PCB.
Replace the HV-DC PCB.Replace the HV-AC PCB.
E068 The high-voltage output has a fault. (separation charging assembly) 
0000 A fault (leak) has been detected while the separation charging assembly is being supplied with high voltage.
Remove and mount the transfer/ separation charging assembly. 
Disconnect and then connectJ7233 and J734 of the HV-DC PCB. Disconnect and then connect J741 and J742 of theHV-AC PCB. Replace the HV-AC PCB. 
Replace the transfer/ separation charging assembly.
Replace pre-transfer charging assembly.

E069 The transfer high voltage has an error. 
0000 A fault (leak) has been detected while the transfer charging assembly is being supplied with high voltage.
Remove and mount the transfer/ separation charging assembly. Check for soiling.
Disconnect and then connect T701 and J723 of the HV-DC PCB. Replace the HV-DC PCB.
Replace the pre-transfer charging assembly..

Thousands of Parts and Free Shipping

 

Errorcodes E012 To E020 and Solution for Canon ImageRunner IR7105/7095/7086

E012 The drum motor rotation is faulty.

0000After the drum motor has gone on, the PLL lock signal of the motor is not detected for 2 sec or more.

Disconnect and then connect J1721 of the relay PCB.
Disconnect and then connect J512 of the DC controller PCB. Disconnect and then connect J601 and J602 of the drum motor.

Replace the drum motor. Replace the DC controller PCB.

E013 The waste toner feedscrew is stuck. (clogged with waste toner)         

After correcting the fault, be sure to reset the error.(COPIER>FUNCTION>CLEAR>ERR)
0000 The waste toner feedscrew is stuck for 4 sec or more.

Detach and then attach the waste toner pipe.

Replace the waste toner pipe.

Replace the waste toner feedscrew detecting switch.

Replace the DC controller PCB.

0010The power has been turned off and then on without resetting the error.

Reset the error. (COPIER>FUNCTION>CLEAR>ERR)

E014 The fixing motor rotation is faulty.
0000 After the fixing motor has gone on, the PLL signal of the motor is not detected for 2 sec or more.

Disconnect and then connect J651 and J652 of the fixing motor.

Replace the fixing motor.
Replace the relay PCB.
Replace the DC controller PCB.

E015 The pickup motor rotation is faulty.
0000The pickup motor has gone on, but the FG signal of the motor is not detected for 2 sec or more.

Disconnect and then connect J621 and J622 of the pickup motor.

Replace the pickup motor.Replace the relay PCB. Replace the DC controller PCB.

E019 The waste toner case is full.
0000After the waste toner case has become full, 50,000 prints (A4) or more have been made
without disposing of the waste toner.

Dispose of the waste toner. Check the operation of the waste toner bottle base.

Disconnectand then connect J514 of the DC controller PCB.
Replace the waste toner case full sensor. Replace the DC controller PCB.

E020 The developing assembly is out of toner. The buffer motor rotation is faulty. The toner feed motor (sub hopper) rotation is faulty.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0001The absence of toner inside the developing assembly is detected of 120 sec or more even when toner supply operation has been executed for the assembly.

Disconnect and then connect the connector (J504, J512) of the DC controller PCB.

Replace the developing cylinder clutch (CL4).

Replace the buffer motor (M18).
Replace the magnet roller drive clutch (CL1).
0002The absence of toner in the buffer is detected for 60 sec even after toner supply

operation for the buffer has been executed and when there is toner inside the hopper.Disconnect and connect the connector (J504, J511) of the DC controller PCB.

Replace the buffer motor (M18).
Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2).
0003The absence of toner inside the buffer is detected for 210 sec or more even when there is

toner inside the sub hopper and after toner supply operation of that buffer following the
replacement of the toner bottle.

Disconnect and connect the connector (J504, J511) of the DC controller PCB.
Replace the buffer motor (M18).Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch(sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2).
0004 The absence of toner inside he buffer is detected for 150 sec or more even when there is

toner inside the buffer and after toner supply operation has been executed for
the buffer following the replacement of the toner bottle.

Disconnect and connect the connector (J504, J511) of the DC controller PCB.

Replace the buffer motor (M18).Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch(sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2).
0005When installation mode (COPIER>FUNCTION>INSTALL>TONER-S) is

executed, the developing assembly inside toner sensor does not detect the presence of toner.

Disconnect and then connect the connector (J504) of the DCcontroller PCB.
Replace the developing assembly inside toner sensor (TS3).
0006When installation mode (COPIER>FUNCTION>INSTALL>TONER-S) is

executed, the developing assembly inside toner sensor detects the presence of toner, but it
does not detect the presence for 600 sec or more thereafter.

Disconnect and then connect the connector (J504) of the DCcontroller PCB.

Replace the developing assembly inside toner sensor (TS3).
0007When installing mode (COVER>FUNCTION>INSTALL>TONER-S) is

executed, the buffer inside toner sensor does not detect the presence of toner for 60 sec or more.

Disconnect and connect the connector (J504, J511) of the DC controller PCB.

Replace toner transport motor (sub hopper; M22), toner transport clutch(sub hopper; CL23), buffer inside toner sensor (TS1),
0008When the toner feed motor (sub hopper) is driven, a fault is detected for 3 sec

or more for the motor.

Disconnect and connect the connector (J511) of the DC controller PCB.

Replace toner transport motor (sub hopper; M22).
0009 There is a fault in the rotation of the buffer motor.

Disconnect and then connect the connector (J504) of the DC controller PCB.

Replace the buffer motor (M18).

0010
The power has been turned off and then on without resetting the error.

Reset the error. (COPIER>FUNCTION>CLEAR>ERR).

Thousands of Parts and Free Shipping