Errorcodes E025 To E069 and Solution for Canon ImageRunner IR7105/7095/7086

 

E025 The toner bottle motor rotation is faulty.
0000 A toner bottle motor error (over-current) is detected for 10 sec for a second time.
MEMO:
The 1st detection of the error will cause the machine to indicate the message.
"Shake and Replace the Toner Container."
Disconnect and then connect J512 of the DC controller PCB.
0001 The toner bottle motor is not connected.
MEMO:
The 1st detection of the error will cause the machine to indicate the message.
"Shake and Replace the Toner Container."
Disconnect and then connect J512 of the DC controller PCB.
E032 The copy data controller/NE controller counter fails to operate. 
0001 An open circuit of the counter signal has been detected.

Disconnect and then connect J1022 of the main controller PCB.
Replace the copy data controller/NE controller.
Replace the main controller PCB.
E043 The rotation of the pickup motor of the side paper deck is faulty. 
0000 The side paper deck pickup motor has gone on, but the PLL lock signal is not
detected for 2 sec or more (1st detection).
MEMO:
For the 2nd and subsequent detection, the machine will indicate "E043" on the
screen offering a choice of sources of paper.

Disconnect and then connect J101 and J106 of the side paper deck driver PCB.
Replace the pickup motor.Replace the side paper deck driver PCB.
Replace the DC controller PCB.
E051 The horizontal registration HP detection has an error. 
0001 After the start of horizontal registration HP detection, the HP sensor is not off
within 5 sec (i.e., not leaving home position).
MEMO:
If an error is detected in the course of horizontal registration HP detection at
power-on, the machine will indicate the presence of a jam.

Replace the horizontal registration HP sensor.Replace the horizontal registration motor.
Replace the stackless transport driver PCB.Replace the DC controller PCB.
0002 After the start of horizontal registration HP detection, the home position is not detected within 5 sec.
MEMO:
If an error is detected in the course of horizontal registration HP detection at
power-on, the machine will indicate the presence of a jam.
Replace the horizontal registration HP sensor.Replace the horizontal registration motor.
Replace the stackless transport driver PCB.
Replace the DC controller PCB.
0003 At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec.

Replace the horizontal registration HP sensor.Replace the horizontal registration motor.
Replace the stackless transport driver PCB.Replace the DC controller PCB.

E065 The high-voltage output has a fault. (primary charging assembly)
0000 A fault (leak) is detected when high voltage is supplied to the primary charging assembly.

Remove and then mount the primary charging assembly.Check for soiling.
Disconnect and then connect T601, J723, and J731 of the HV-DC PCB.
Replace the HV-DC PCB.
E067 The high-voltage output has a fault.
0000 A fault is detected at the same time in 2 of the following: primary high voltage, pre-transfer
high voltage, transfer high voltage, separation high voltage.

Remove and mount the primary charging assembly.
Remove and mount the pre-transfer charging assembly.
Remove and mount the transfer/ separation charging assembly.
Disconnect and then connect J721, J723, J731, and J734 of the HV-DC PCB.
Replace the HV-DC PCB.Replace the HV-AC PCB.
E068 The high-voltage output has a fault. (separation charging assembly) 
0000 A fault (leak) has been detected while the separation charging assembly is being supplied with high voltage.
Remove and mount the transfer/ separation charging assembly. 
Disconnect and then connectJ7233 and J734 of the HV-DC PCB. Disconnect and then connect J741 and J742 of theHV-AC PCB. Replace the HV-AC PCB. 
Replace the transfer/ separation charging assembly.
Replace pre-transfer charging assembly.

E069 The transfer high voltage has an error. 
0000 A fault (leak) has been detected while the transfer charging assembly is being supplied with high voltage.
Remove and mount the transfer/ separation charging assembly. Check for soiling.
Disconnect and then connect T701 and J723 of the HV-DC PCB. Replace the HV-DC PCB.
Replace the pre-transfer charging assembly..

Thousands of Parts and Free Shipping