Canon ImageRunner Advance 8205 8295 8285,Errorcode E804 To E996 and Solution

E804 -0000 -05 Title Power Supply Cooling Fan 1/2 error

Detection description The Fan stop signal is detected for 5 seconds or longer and

retry is failed 4 times in a row although the Power Supply Cooling Fan 1 (FM14)/Power Supply Cooling Fan 2 (FM15) is turned ON.The error detection signal cable is shared with the Fans, and it

is not detected with which Fan the error occurs.

Remedy 1. Check the connection of the Connector.

2. Replace the Power Supply Cooling Fan 1 (FM14)/Power Supply Cooling Fan 2 (FM15).

E804 -0001 -05 Title Fixing Power Supply Cooling Fan error

Detection description The Fan stop signal is detected for 1.5 seconds or longer

and retry is failed 4 times in a row although the Fixing Power Supply Cooling Fan (FM7) is turned ON.

Remedy 1. Check the connection of the Connector.

2. Replace the Fixing Power Supply Cooling Fan (FM7).

E806 -0000 -05 Title Making Image Exhaust Fan error

Detection description The Fan stop signal is detected for 5 seconds or longer and

retry is failed 4 times in a row although the Making Image Exhaust Fan (FM3) is turned ON.

Remedy 1. Check the connection of the Connector.

2. Replace the Making Image Exhaust Fan (FM3).

E808 -0001 -05 Title Fixing Power Supply error

Detection description Detected 290 V or higher inlet voltage at power-on.

Remedy 1. Check the outlet voltage. -> Connect to the correct outlet.

2. Check the connection between the Main Driver PCB (PCB2)

and the Fixing Power Supply PCB (PCB10).

3. Replace the Fixing Power Supply PCB (PCB10).

4. Replace the Main Driver PCB (PCB2).

E808 -0002 -05 Title Fixing Power Supply error

Detection description Detected 50 V or lower inlet voltage at power-on.

Remedy 1. Check the outlet voltage. -> Connect to the correct outlet.

2. Check the connection between the Main Driver PCB (PCB2)

and the Fixing Power Supply PCB (PCB10).

3. Replace the Fixing Power Supply PCB (PCB10).

4. Replace the Main Driver PCB (PCB2).

E808 -0003 -05 Title Fixing Power Supply error

Detection description Inlet current is 1 A or lower for 1 second or longer although the

maximum voltage is output.

Remedy 1. Check the clogging of the Fixing Power Supply Cooling Fan (FM7).

2. Check the clogging of the Louver on right side of the host machine (Multi-purpose Tray side).

3. Check the connection of the Fixing Power Supply PCB (PCB10) Output Connector.

4. Replace the Fixing Power Supply PCB (PCB10).

E808 -0004 -05 Title Fixing Power Supply error

Detection description Detected OFF with 12 V of the Main Driver PCB (PCB2) output.

Remedy Replace the Main Driver PCB (PCB2).

E808 -0005 -05 Title 12 V OFF detection when relay is turned ON

Detection description  Detected OFF with 12 V of the Fixing Power Supply output

after IH relay is turned ON.

Remedy 1. Check the conduction of the Fixing Thermal Switch 1/2 (TP1/2).

2. Check the drawer between the Fixing Assembly and the host machine.

3. Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB(PCB10).

4. Replace the Fixing Power Supply Unit.

5. Replace the Main Driver PCB (PCB2).

E808 -0006 -05 Title ASIC error

Detection description ASIC error.

Remedy Replace the DC Controller PCB (PCB1).

E808 -0007 -05 Title Fixing Power Supply error

Detection description The detected power voltage differs from the voltage of the port in the IH Power Supply.

Remedy 1. Check the connection between the Main Driver PCB (PCB2)  and the Fixing Power Supply PCB (PCB10).

2. Replace the Fixing Power Supply PCB with the one for the correct location (voltage).

3. Replace the DC Controller PCB (PCB1).

E808 -0008 -05 Title Fixing Power Supply error

Detection description Current fluctuation error.

Remedy 1. Check the connection between the Main Driver PCB (PCB2)

and the Fixing Power Supply PCB (PCB10).

2. Check the connection between the Fixing Power Supply PCB (PCB10) and the Heater Unit.

3. Replace the Fixing Roller and Heater Unit.

4. Replace the Fixing Power Supply PCB (PCB10).

5. Replace the Main Driver PCB (PCB2).

E808 -0009 -05 Title Fixing Power Supply error

Detection description Unable to clear the error flag at power-on.

Remedy Replace the DC Controller PCB (PCB1).

E820 -0000 -05 Title Developer Lower Cooling Fan error

Detection description The Fan stop signal is detected for 5 seconds or longer and

retry is failed 4 times in a row although the Developer Lower Cooling Fan (FM30) is turned ON.

Remedy 1. Check the connection of the Connector.

2. Replace the Developer Lower Cooling Fan (FM30).

E820 -0001 -05 Title Developer Upper Cooling Fan error

Detection description The Fan stop signal is detected for 5 seconds or longer and

retry is failed 4 times in a row although the Developer Upper Cooling Fan (FM31) is turned ON.

Remedy 1. Check the connection of the Connector.

2. Replace the Developer Upper Cooling Fan (FM31).

E820 -0002 -05 Title Duplex Driver Cooling Fan error

Detection description The Fan stop signal is detected for 5 seconds or longer and

retry is failed 4 times in a row although the Duplex Driver Cooling Fan (FM41) is turned ON.

Remedy 1. Check the connection of the Connector. 2. Replace the Duplex Driver Cooling Fan (FM41).

E824 -0000 -05 Title Primary Charging Air Supply Fan error

Detection description The Fan stop signal is detected for 5 seconds or longer and

retry is failed 4 times in a row although the Primary Charging Air Supply Fan (FM2) is turned ON.

Remedy 1. Check the connection of the Connector.

2. Replace the Primary Charging Air Supply Fan (FM2).

E840 -0001 -05 Title Fixing Shutter Motor error

Detection description The Fixing Shutter HP Sensor (PS53) failed the detection at

the Fixing Shutter operation.

Remedy 1. Check the operation of the Fixing Shutter Gear (overload, etc.).

2. Check the operation of the Fixing Shutter Motor (M15) at the initialization operation of the Fixing Shutter.

3. Check the detection of the Fixing Shutter HP Sensor (PS53) (if the Sensor operates normally).

4. Check the drawer of the Fixing Assembly and the host machine.

5. Replace the Fixing Upper Unit and the Fixing Drawer Harness Unit.

6. Replace the Main Driver PCB (PCB2) (check the fuse (FU11)).

E880 -0001 00 Title Controller Fan error

Detection descriptionError in the Main Controller Cooling Fan (FM4) is detected.

Remedy Connector disconnection, failure of Fan.

E880 -0005 00 Title Controller Fan error

Detection description Error in the HDD Cooling Fan (FM) is detected.

Remedy Connector disconnection, failure of Fan.

E905 -0001 -05 Title POD Deck Air Assist Fan error

Detection description [POD Deck Lite] When the Air Assist Swing Motor fails to return

to the HP although a specified period of time has passed

Remedy 1. Check connector disconnection/improper connection. => Disconnect and then connect the connector. Target connector: Deck Lite Controller J04, J05

BoxDriver J51, J52, J57

2. Replace the Swing Motor (M3) and the Air Assist Fan (FM1, FM2, FM3).

3. Replace the Deck Lite Controller PCB.

4. Replace the BoxDriver PCB.

E905 -0002 -05 Title POD Deck Air Assist Fan error

Detection description [POD Deck Lite] When the Pickup Motor Cooling Fan is not locked

Remedy 1. Check connector disconnection/improper connection. =>Disconnect and then connect the connector.

Target connector: Deck Lite Controller J30

2. Replace the Motor Cooling Fan (FM4).

3. Replace the Deck Lite Controller PCB.

E905 -0003 -05 Title POD Deck Air Assist Fan error

Detection description [POD Deck Lite] When the Pickup Motor Cooling Fan is not unlocked

Remedy 1. Check connector disconnection/improper connection. =>

Disconnect and then connect the connector.

Target connector: Deck Lite Controller J30

2. Replace the Motor Cooling Fan (FM4).

3. Replace the Deck Lite Controller PCB.

E906 -0001 -05 Title POD Deck Air Heater error

Detection description [POD Deck Lite] Air Heater high temperature error

When 120 deg C or higher temperature is detected for 1 second consecutively

Remedy 1. Check connector disconnection/improper connection. => Disconnect and then connect the connector.Target connector: Deck Lite Controller J03, J05BoxDriver J52, J54, J58, J59

2. Replace the Air Heater.

3. Replace the Deck Lite Controller PCB.

E906 -0002 -05 Title POD Deck Air Heater error

Detection description [POD Deck Lite] Air Heater low temperature error

When the heater does not become Ready although a specified period of time has passed

Remedy 1. Check connector disconnection/improper connection. => Disconnect and then connect the connector.Target connector: Deck Lite Controller J03, J05 BoxDriver J52, J54, J58, J59

2. Replace the Air Heater.

3. Replace the Deck Lite Controller PCB.

E996 -xxxx -05 Title Timeout error

Detection description The DC Controller is not stopped. The Detailed Code varies according to the state transition of the software.

Remedy Turn OFF and then ON the main power.

E996 -0071 -04 Title Frequent error avoidance jam (ADF)

Detection description Frequent error avoidance jam (ADF)

Remedy Depending on the setting of JM-ERR-R in service mode, “010071” jam is displayed as an error.

Collect log and contact to the sales companies. To cancel the setting, select COPIER> OPTION> FNC-SW> JM-ERR-R, and set JM-ERR-R to 0.

E996 -0CA1 -05 Title Frequent error avoidance jam (PRINTER)

Detection description Error avoidance jam (PRINTER)

Remedy Make “000CA1” jam to be displayed as an error by setting JMERR-D in service mode.

Collect log and contact to the sales companies. To cancel the setting, select COPIER> OPTION> FNC-SW>JM-ERR-D, and set JM-ERR-D to 0.

E996 -0CA2 -05 Title Frequent error avoidance jam (PRINTER)

Detection description Error avoidance jam (PRINTER)

Remedy Make “000CA2” jam to be displayed as an error by setting JMERR- D in service mode.

Collect log and contact to the sales companies.To cancel the setting, select COPIER> OPTION> FNC-SW>JM-ERR-D, and set JM-ERR-D to 0.

E996 -0CA3 -05 Title Frequent error avoidance jam (PRINTER)

Detection description Error avoidance jam (PRINTER)

Remedy Make “000CA3” jam to be displayed as an error by setting JMERR-D in service mode.

Collect log and contact to the sales companies. To cancel the setting, select COPIER> OPTION> FNC-SW> JM-ERR-D, and set JM-ERR-D to 0.

E996 -0CA4 -05 Title Frequent error avoidance jam (PRINTER)

Detection description Error avoidance jam (PRINTER)

Remedy Make “000CA4” jam to be displayed as an error by setting JMERR- D in service mode.

Collect log and contact to the sales companies.To cancel the setting, select COPIER> OPTION> FNC-SW>JM-ERR-D, and set JM-ERR-D to 0.

E996 -0CA4 -05 Title Frequent error avoidance jam (PRINTER)

Detection description Error avoidance jam (PRINTER)

Remedy Make “000CA4” jam to be displayed as an error by setting JMERR-

D in service mode.

E996 -0CAF -05 Title Frequent error avoidance jam (PRINTER)

Detection description Error avoidance jam (PRINTER)

Remedy Make “000CAF” jam to be displayed as an error by setting JMERR- D in service mode.

Collect log and contact to the sales companies.To cancel the setting, select COPIER> OPTION> FNC-SW>JM-ERR-D, and set JM-ERR-D to 0.Collect log and contact to the sales companies.

To cancel the setting, select COPIER> OPTION> FNC-SW>JM-ERR-D, and set JM-ERR-D to 0.