1. Check the connection of the Connector. Motor side: J2319, Main Driver PCB (PCB2) side: J109
2. Check the voltage of the Developing Motor (M2) J2152.
If voltage is 0V, check the connection of the Relay PCB J520.
3. Check the load of the Developing Motor (M2).
Manually turn the Developing Motor (M2) located at the rear of the host machine to check it.
4. Replace the Developing Motor (M2).
5. Replace the Developing Clutch (CL1). (When an error occurs while the Developing Clutch is ON.)
6. Replace the Main Driver PCB (PCB2). 7. Replace the DC Controller PCB (PCB1).
Description Lock error of the Developing Motor (M2).
E023-0002 -05 Title Error in Magnet Roller Clutch connection detection
Remedy
1. Check the connection of the Magnet Roller Clutch (CL5).
Sensor side: J2006, Main Driver PCB (PCB2) side: J109
2. Replace the Magnet Roller Clutch (CL5). 3. Replace the Main Driver PCB (PCB2).
4. Replace the DC Controller PCB (PCB1).
Description Connection of the Magnet Roller Clutch (CL5) cannot be detected 5 times with 20 msec time interval.
E025-0001 -05 Title Toner Feed Motor error
Remedy
1. Check the connection of the Connector. Motor side: J2036, Buffer Unit relay: J3124, Front side
relay: J3090, Rear side relay: J3091, Main Driver PCB (PCB2) side: J115
2. Replace the Toner Feed Motor (M28).
3. Check if toner is clogged inside of the Buffer.
Turn the Drive Shaft of the Motor with your hand to checkit. If the load is too much, inside of the Buffer may be clogged, so clean inside of it.
4. Replace the Main Driver PCB (PCB2).
5. Replace the DC Controller PCB (PCB1).
Description Overcurrent of the Toner Feed Motor (M28) was detected.
E027-0001 -05 Title Toner Supply Motor error
Remedy
1. Check the connection of the Connector.Motor side: J2037, Front side relay: J3080, Rear side relay:
J3063, Main Driver PCB (PCB2) side: J117
2. Remove the Toner Container, and check if an error occurs. If an error does not occur, reinstall the Toner Container and check again. If an error occurs, check the driving area of connection point of the container.
If an error occurs, go on to 3.
3. Replace the Toner Supply Motor (M10).
4. Replace the Main Driver PCB (PCB2).
5. Replace the DC Controller PCB (PCB1).
Description Lock error of the Toner Supply Motor (M10).
E032-0001 -00 Title Failure of NE Controller Counter
Remedy Disconnection of cable.
Description Detection of open circuit of count pulse signal.
E041-0001 -05 Title Right Deck Lifter Motor error
Remedy
1. Check for displacement of the Lifter Wire of the Right Deck.
2. Check for hindrance to smooth movement of the Deck Base Plate of the Right Deck.
Description Overcurrent of the Right Deck Lifter Motor was detected.
E041-0002 -05 Title Left Deck Lifter Motor error
Remedy 1. Check for displacement of the Lifter Wire of the Left Deck.
2. Check for hindrance to smooth movement of the Deck Base Plate of the Left Deck.
Description Overcurrent of the Leftt Deck Lifter Motor was detected.
E041-0003 -05 Title Cassette 3 Lifter Motor error
Remedy
1. Check for error around the Lifter of the Cassette 3.
2. Check for hindrance to smooth movement of the Cassette Base Plate of the Cassette 3.
Description Overcurrent of the Cassette 3 Lifter Motor was detected.
E041-0004 -05 Title Cassette 4 Lifter Motor error
Remedy 1. Check for error around the Lifter of the Cassette 4.
2. Check for hindrance to smooth movement of the Cassette Base Plate of the Cassette 4.
Description Overcurrent of the Cassette 4 Lifter Motor was detected.
E053 -0001 -05 Title Error in Reverse Upper Flapper Solenoid connection detection
Remedy
1. Check the connection of the Reverse Upper Flapper
Solenoid (SL5).Solenoid side: J2115, Duplex Driver PCB side: J340
2. Replace the Reverse Upper Flapper Solenoid (SL5).
3. Replace the Duplex Driver PCB (PCB4).
4. Replace the DC Controller PCB (PCB1).
Description Connection of the Reverse Upper Flapper Solenoid (SL5)
cannot be detected 5 times with 20 msec time interval.
Thousands of Parts and Free Shipping
No comments:
Post a Comment