Thousands of Parts and Free Shipping
Detection description The aligning plate does not return to aligning plate
front home
position Sensor when the alignment plate front Motor has been driven for 4 seconds.
Remedy 1. The front Aligning
Plate Home Position Sensor (PI106) is faulty.
2. The wiring between the Finisher Controller PCB and front aligning plate Motor is faulty.
3. The front aligning plate is faulty. 4.
The front aligning plate Motor (M103) is faulty.
5. The Finisher Controller PCB is faulty.
E531-8001 -05
Title Staple home position error (Finisher-P1)
Detection description The Stapler does not leave the staple home position when
the
Staple Motor has been driven for 0.4 sec.
Remedy 1. The wiring between the
Finisher Controller PCB and Stapler is faulty.
2. The Stapler is faulty. 3. The Finisher
Controller PCB is faulty.
E531-8002 -05
Title Staple home position error (Finisher-P1)
Detection description
The Stapler does not return to the staple home position when
the Staple Motor has been driven for 0.4 sec.
Remedy 1. The wiring between
the Finisher Controller PCB and Stapler is
faulty.
2. The Stapler is faulty. 3. The Finisher
Controller PCB is faulty.
E532-8001 -05
Title Stapler shift home position error (Finisher-P1)
Detection description The Stapler does not leave the stapler shift home
pposition
when the Stapler Shift Motor hasbeen driven for 5 seconds.
Remedy 1. The Stapler Drive Home
Position Sensor (PI110) is faulty.
2. The wiring between the Finisher Controller PCB and Stapler Shift Motor is faulty.
3. The stapler shift base is faulty. 4.
The Stapler Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
E532-8002 -05
Title Stapler shift home position error (Finisher-P1)
Detection description The Stapler does not return to the stapler shift home
position
when the Stapler Shift Motor has been driven for 20 seconds.
Remedy 1. The Stapler Drive
Home Position Sensor (PI110) is faulty.
2. The wiring between the Finisher Controller PCB and Stapler Shift Motor is faulty.
3. The stapler shift base is faulty. 4.
The Stapler Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
E535 -8001 -05
Title Swing home position error (Finisher-P1)
Detection description The Stapler does not leave the swing home position when
the
Swing Motor has been driven for 3 seconds.
Remedy 1. The Swing Home
Position Sensor (PI105) is faulty.
2. The wiring between the Finisher Controller PCB and Swing Motor is faulty.
3. The swing mechanism is faulty. 4. The Swing Motor (M106)
is faulty.
5. The Finisher Controller PCB is faulty.
E535-8002 -05
Title Swing home position error (Finisher-P1)
Detection description The Stapler does not return to the swing home position
when
the Swing Motor has bee driven for 3 seconds.
Remedy 1. The Swing Home
Position Sensor (PI105) is faulty.
2. The wiring between the Finisher Controller PCB and Swing Motor is faulty.
3. The swing mechanism is faulty. 4. The Swing Motor (M106)
is faulty.
5. The Finisher Controller PCB is faulty.
E537-8001 -05 Title Rear aligning plate home position
error (Finisher-P1)
Detection description The aligning plate does not leave the Aligning Plate Rear Home Position Sensor when
the Alignment Plate Rear Motor has been driven for 4
seconds.
Remedy 1. The Aligning Plate
Rear Home Position Sensor (PI107) is faulty.
2. The wiring between the Finisher Controller PCB and Aligning Plate Rear Motor is faulty.
3. The rear aligning plate is faulty. 4.
The Rear Aligning Plate Motor (M104) is faulty.
5. The Finisher Controller PCB is faulty.
E537-8002 -05
Title Rear aligning plate home position error (Finisher-P1)
Detection description The aligning plate does not return to Aligning Plate Rear
Home Position Sensor when the Alignment Plate Rear Motor has been driven for 4 seconds.
Remedy 1. The Aligning Plate
Rear Home Position Sensor (PI107) is faulty.
2. The wiring between the Finisher Controller PCB and Aligning Plate Rear Motor is faulty.
3. The rear aligning plate is faulty. 4.
The Rear Aligning Plate Motor (M104) is faulty.
5. The Finisher Controller PCB is faulty.
E540-8001 -05 Title Tray 1 time out error (Finisher-P1)
Detection description
1. If the tray does not return to home position when the Tray 1
Shift Motor is driven for 25 seconds.
2. If the tray does not move to other area when Tray 1 Shift Motor is driven for 5 seconds.
Remedy 1. The Tray 1 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty. 4.
The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
E540-8002 -05 Title Tray 1 shift area error (Finisher-P1)
Detection description
1. The dangerous area is reached before the Tray 1 Paper
Surface Sensor detects paper surface during the paper surface detection operation.
2. A discontinuous area is detected during tray operation.
Remedy 1. The Tray 1 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
E540-8003 -05 Title Swing Guide Switch/Staple Safety
Switch error (Finisher-P1)
Detection description
The swing guide switch or staple safety switch is activated while the tray is operating.
Remedy 1. The Tray 1 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty. 4.
The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
E540-8004 -05 Title The Tray 1 Shift Motor clock error
(Finisher-P1)
Detection description
The FG input cannot be detected when the Tray 1 Shift Motor has been driven for 0.2 second.
Remedy 1. The Tray 1 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
E540-8005 -05 Title The Tray 1 Shift Motor speed error
(Finisher-P1)
Detection description
The lock detection signal turns OFF 150 msec after the lock
detection signal turned ON.
Remedy 1. The Tray 1 Shift Area Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty. 4.
The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty
E540-8006 -05 Title The Tray 1 Shift Motor acceleration
error (Finisher-P1)
Detection description
The lock detection signal does not turn ON when the Tray 1
Shift Motor has been driven for 1 second.
Remedy 1. The Tray 1 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty. 4.
The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
E540-8007 -05 Title The Tray 1 Shift Motor error
(Finisher-P1)
Detection description
The lock detection signal does not turn OFF when the Tray 1
Shift Motor is at a stop.
Remedy 1. The Tray 1 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty. 5.
The Finisher Controller PCB is faulty.
E542 -8001 -05 Title Tray 1 time out error (Finisher-P1)
Detection description
1. If the tray does not return to home position when the Tray 1 Shift Motor is driven for 25 seconds.
2. If the tray does not move to other area when Tray 2 Shift Motor is driven for 5 seconds.
Remedy 1. The Tray 2 shift area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty. 4.
The Tray 2 shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
E542-8002 -05
Title Tray 2 shift area error (Finisher-P1)
Detection description
1. The upper limit area is reached before the Tray 2 Paper Surface Sensor 1 detects the paper surface during paper surface detection operation.
2. A discontinuous area is detected during tray operation.
3. During evacuation operation, arrival at the area beyond the Tray 2 Paper Surface Sensor 2 is detected before this Sensor detects paper surface.
Remedy 1. The Tray 2 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty. 4.
The Tray 2 Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
E542-8004 -05 Title The Tray 2 Shift Motor clock error
(Finisher-P1)
Detection description
The FG input cannot be detected when the Tray 2 Shift Motor has been driven for 0.2 second.
Remedy 1. The Tray 2 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty. 4.
The Tray 2 Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
E542-8005 -05 Title The Tray 2 Shift Motor speed error
(Finisher-P1)
Detection description
The lock detection signal turns OFF 150 msec after the lock detection signal turned ON.
Remedy 1. The Tray 2 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty. 4.
The Tray 2 Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
E542-8006 -05 Title The Tray 2 Shift Motor acceleration
error (Finisher-P1)
Detection description
The lock detection signal does not turn ON when the Tray 2
Shift Motor has been driven for 1 second.
Remedy 1. The Tray 2 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.4. The Tray 2 Shift Motor (M105)
is faulty.
5. The Finisher Controller PCB is faulty.
E542-8007 -05 Title The Tray 2 Shift Motor error
(Finisher-P1)
Detection description
The lock detection signal does not turn OFF when the Tray 2 Shift Motor is at a stop.
Remedy 1. The Tray 2 Shift Area
Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 2 Shift Motor (M105) is faulty.
No comments:
Post a Comment