0007 There is a JIBIG encode error.
000d There is a JBIG decode error.
- Turn off and then back on the
power.
E400 There is an ADF
communication error.
0001 There is a check sum error. - Check the connector for any fault
inconnection.
0002 There is a reception status error.
0003 There is a reception interrupt error.
- Replace the reader controller PCB.
- Replace the ADF controller PCB.
E413 There is a fault in the
ADF shift motor.
0001 The output of the shift HP sensor is identified as indicating open.
0002 The output of the shift HP sensor is identified as indicating closed.
- Check the connector for any fault
in connection.
- Replace the sensor and motor in question.
- Check the mounting condition of
the area around the cam.
E490 The ADF type is wrong.
0001 The ADF is not of a supported type.
- Replace the ADF with a supported type.
E503 There is an error in the
finisher internal communication (finisher).
0002 There is an error in the communication between the finisher and the
saddle unit.
- Check the connection between the saddle
stitcher controller PCB and the finisher controller PCB.
0003 There is an error in the communication between the finisher and the punch
unit.
- Check the communication between
the saddle stitcher controller PCB and the finisher controller PCB.
E505 There is a finisher backup memory error (finisher).
0001 An error has occurred in the data stored in the backup memory.
- Turn off the main power; check the
DC controller PCB and the finisher controller PCB for wiring;
check the 24-V system fuse; then,
turn the main power back on.
0002 There is an error in the punch unit EEPROM data.
- Turn off the main power; check the
DC controller PCB and the puncher controller PCB for wiring; then, check the
24-V system fuse; then, turn the main power back on.
E514 There is a trailing edge
assist motor error (finisher).
8001 The home position sensor does not go off even when the trailing edge
assist motor
has rotated for a specific period of
time.
1. Check the trailing edge assist
home position sensor. Is the sensor normal?
2. Check the wiring between the
finisher controller PCB and the trailing edge assist
motor. Is it normal?
3. Check the trailing edge assist mechanism.
Is there a fault?
4. Try replacing the trailing edge
assist motor. Is the problem corrected?
8002 The home position sensor does not go on even when the trailing edge
assist motor
has rotated for a specific period of
time.
E519 There is a gear change
motor error (finisher).
8001 The home position sensor does not go off even when the
gear change motor has
rotated for a specific period of
time.
1. Check the gear change home
position sensor. Is the sensor normal?
2. Check the wiring between the
finisher controller PCB and the change motor. Is it normal?
3. Check the gear change mechanism.
Is there a fault?
4. Try changing the gear change
motor. Is the problem corrected?
0002 The home position sensor does not go on even when the gear change motor
has
rotated for a specific period of
time.
E530 There is a front
alignment error. (finisher)
8001 The home position sensor does not go off even when the front alignment
motor has
rotated for a specific period of
time.
1. Check the aligning plate home
position sensor. Is it normal?
2. Check the wiring between the
finisher controller PCB and the aligning plate front motor. Is it normal?
3. Is there any mechanical obstacle
in the path in which the aligning plate moves?
4. Try replacing the aligning plate
front motor. Is the problem corrected?
8002 The home position sensor does not go on even when the front alignment
sensor has
rotated for a specific period of
time.
E531 There is a stapling error. (finisher)
0001 The home position sensor does not go off even when the stapler motor has
rotated for
a specific period of time.
1. Check the wiring between the
finisher controller PCB and the stapler. Is it
normal?
2. Try replacing the stapler. Is the
problem corrected?
0002 The home position sensor does not go on even when the stapler motor has
rotated for
a specific period time.
E532 There is a stapler shift
error. (finisher)
8001 The home position sensor does not go off even when the stapler shift
motor has
rotated for a specific period of
time.
1. Check the stapler shift home
position sensor. Is the sensor normal?
2. Check the wiring between the
finisher controller PCB and the stapler shift
motor. Is it normal?
3. Is there any mechanical obstacle
in the path of the stapler shift base?
4. Try replacing the stapler shift
motor. Is the problem corrected?
8002 The home position sensor does not go on even when the stapler shift motor
has
rotated for a specific period of
time.
E535 There is a swing error.
(finisher)
8001 The home position sensor does not go off even when the wiring motor has
rotated for
a specific period of time.
1. Check the wiring home position
sensor. Is it normal?
2. Check the wiring between the
finisher controller PCB and the swing motor. Is it normal?
3. Is there a fault in the swing mechanism?
4. Try replacing the swing motor. Is
the problem corrected?
8002 The home position sensor does not go on even when the swing motor has
rotated for
a specific period of time.
E537 There is a rear
alignment error. (finisher)
8001 The home position sensor does not go off even when the swing motor has rotated
for
a specific period of time.
1. Check the aligning plate rear
home position sensor. Is it normal?
2. Check the wiring between the
finisher controller PCB and the aligning plate rear
motor. Is it normal?
3. Is there a mechanical obstacle in
the path of the aligning plate?
4. Try replacing the aligning plate
rear motor. Is the problem corrected?
8002 The home position sensor does not go on even when the swing motor has
rotated for
a specific period of time.
E540 There is an upper tray ascent/decent error. (finisher)
8001 There is a fault in the upper tray ascent/ descent motor clock.
1. Check the No. 1 tray area sensors
1 through 3. Are they normal?
2. Check the wiring between the
finisher controller PCB and the No. 1 tray shift motor. Is it normal?
3. Is there a fault in the tray
ascent/descent mechanism?
4. Try replacing the No. 1 tray
shift motor. Is the problem corrected?
8002 There is an area fault.
8003 The safety switch has gone on.
E542 There is a lower tray
ascent/descent error. (finisher)
8001 There is a fault in the lower tray ascent/ descent motor clock signal.
8002 There is an area error.
0003 The safety switch has activated.
1. Check the No. 2 tray area sensors
1 through 3. Are the sensors normal?
2. Check the wiring between the
finisher controller PCB and the No. 2 tray shift motor. Is it normal?
3. Is there a fault in the tray
ascent/descent mechanism?
4. Try replacing the No. 2 tray
shift motor. Is the problem corrected?
E584 There is a shutter unit
error. (finisher)
8001 The shutter open sensor fails to go off. (The shutter does not close.)
0002 The shutter open sensor does not go on. (The shutter does not open.)
1. Check the shutter home position sensor.
Is it normal?
2. Check the wiring between the
finisher controller PCB and the stack feeding
motor and between the finisher
controller PCB and the shutter open/close clutch. Is
it normal?
3. Is there a fault in the shutter mechanism?
4. Try replacing the stack edging
motor and the shutter open/close clutch. Is the
problem corrected?
No comments:
Post a Comment