Detection description HDD failed to be recognized. Startup partition (BOOTDEV)
failed to be found at startup.
Remedy 1. Turn OFF the main switch and check connection of HDD
cable, and then turn ON the main switch.
2. If the Encryption Board has been installed, there may be an Encryption Board failure. In this case, disconnect the signal cable connecting to the Encryption Board and directly connect to the HDD. (It cannot be connected from the back side. Open the Main Controller Cover, and connect by going over the Main Controller PCB 1.) After connecting, power
on by the safe mode. If the machine starts normally, replace the Encryption Board as the Encryption Board had failed.
3. Be sure that HDD spins stably (no problem in drive sound) and 5V/12V power Is supplied when the main power is turned ON. (If the drive sound is abnormal, replace the
HDD.)
4. Replace the HDD and reinstall the system. (In the case of using a USB memory device, insert a USB memory device where the system software has been registered to the slot
of the host machine, and then execute main menu [3]: Upgrade (Overwrite all).)
5. Replace the Main Controller PCB 1.
E602-0002 -00 Title
Error in HDD
Detection description There is no system for the main CPU
Remedy 1. Start in Safe Mode,
then perform overall format using SST or USB memory and
reinstall the system, and then turn OFF and
then ON the Main Switch. (Prepare the USB memory which
system software was registered. Insert the USB
memory to the equipment. Execute [3]: Upgrade (Overwrite All) in the main menu.)
2. If the above measures do not solve the problem, it can be caused by failure with HDD; therefore, replace the HDD and reinstall the system.
E602-0003 -00 Title
Error in HDD
Detection description WriteAbort was detected with BootDevice
Remedy
1. Execute detection and
recovery of WriteAbortSector
<In the case of
display of B/W E-code>
1-1. Perform the following
steps because Service Mode is not available.
1-2. Turn OFF the power.
Then, while pressing 1+9 keys, turn ON the power.
WriteAbortSector recovery routine is automatically started
which makes the screen black.
1-3. After a while, progress
is displayed because the process takes time (40 to
50 min.). The process is complete when the screen
turns white.
<In the case of official display of wrench-mark>
1-1. Set as follows:
CHK-TYPE=0; and execute HDCHECK (40 to 50 min.), and then
turn OFF and then ON the main switch.
2. If the above measures do
not solve the problem, start up in Safe Mode to perform
overall format using SST or USB memory and reinstall the
system, and then turn OFF and
then ON the main switch.
3. If no improvement is
found despite the above measures, it can be caused by failure
with HDD; therefore, replace the HDD and reinstall the
system.
E602-0006 -00 Title
Error in HDD
Detection description There is no system for the sub CPU
Remedy Reinstall the system
software. For details, see “Chapter 6: Upgrading”.
For your reference, the method using USB memory is described
below.
1. Prepare the USB memory
which system software was registered.
2. Execute the following
service mode: COPIER>FUNCTION>SYSTEM>DOWNLOAD
to enter the download mode. (When it
is not operated normally, start the safe mode.)
3. Insert the USB memory to
the equipment.
4. Execute [3]: Upgrade
(Overwrite All) in the main menu. (Be
sure to download SYSTEM, LANGUAGE and RUI.)
5. System software is
downloaded and the machine restarts automatically. At this
time, if the machine restarts with the safe mode, E753 might
occurs. Check the log. In case of
the system software of the options which are not connected, turn OFF and then ON the power supply to restore. (For details, see the description for E753.) If
the measures above do not solve the problem, replace the HDD and download the system software with the foregoing method.
E602-0007 -00 Title
Error in HDD
Detection description There is no ICCProfile
Remedy 1. Start up in Safe Mode
and reinstall the system using SST;
and then turn OFF and then ON the main power switch.
2. If the above measures do not solve the problem, it can be
caused by failure with the HDD; therefore, replace the HDD and reinstall the system.
E602-0009 -00 Title
Error in HDD
Detection description There is no Font file in /BOOTDEV/BOOT
Remedy 1. Start up in Safe Mode
and reinstall the system using SST;
and then turn OFF and then ON the main power switch.
2. If the above measures do not solve the problem, it can be caused by failure with the HDD; therefore, replace the HDD and reinstall the system.
E602-0010 -00 Error
in HDD There is no Chinese, Korean, and Taiwan font files
1. Start up in Safe Mode and reinstall the system using SST;
and then turn OFF and then ON the main power switch.
2. If the above measures do not solve the problem, it can be
caused by failure with the HDD; therefore, replace the HDD
and reinstall the system.
E602-0011 -00 Error
in HDD
There is no Chinese, Korean, and Taiwan font files
1. Start up in Safe Mode and reinstall the system using SST;
and then turn OFF and then ON the main power switch.
2. If the above measures do not solve the problem, it can be
caused by failure with the HDD; therefore, replace the HDD
and reinstall the system.
E602-0012 -00 Title
Error in HDD
Detection description There is no file in which the Web browser refers to
Remedy 1. Start up in Safe Mode
and reinstall the Web browser using
SST, and then turn OFF and then ON the main power switch.
2. If the above measures do not solve the problem, it can be caused by failure with the HDD; therefore, replace the HDD and reinstall the system.
More detail about E602,Please contact me with Email hongcifu@126.com.
More detail about E602,Please contact me with Email hongcifu@126.com.
Thousands of Parts and Free Shipping
No comments:
Post a Comment