E500 -0000 -05 Title Communication error (Finisher-E1)Remedy &wletter5.png" />/span>1. The Finisher Controller PCB is faulty.2. The host machine DC Controller PCB is faulty.
Description The communication with the host machine is interrupted.
E503 -0002 -05 Title Communication error (Finisher-E1)
Remedy
1. The wiring between the Finisher Controller PCB and Saddle Controller PCB is faulty.2. The Finisher Controller PCB is faulty.
3. The Saddle Stitcher Controller PCB is faulty.
Description The communication with the Saddle Stitcher is interrupted.E503 -0003 -05 Title Communication error (Finisher-E1/External 2 Hole Puncher)
Remedy
1. The wiring between the Finisher Controller PCB and host machine DC Controller PCB is faulty.2. The Punch Controller PCB is faulty.
3. The Finisher Controller PCB is faulty.
4. The host machine DC Controller PCB is faulty.
Description The communication with the Puncher unit is interrupted.
E503 -0004 -05 Title A. Communication error (Finisher-E1)
B. Communication error with Insertion Unit (Document Insertion Unit-L1)
C. Communication error with Insertion Unit (Document Insertion/Folding Unit-H1)
Remedy
A-1. The wiring between the Finisher Controller PCB and host machine Controller PCB is faulty.A-2. The Finisher Controller PCB is faulty.
A-3. The host machine Controller PCB is faulty.
B-1. Inserter Controller PCB is faulty.
B-2. Disconnection of communication cable
B-3. Connector on the Inserter Controller PCB is disconnected.
C-1. Folder Controller PCB is faulty.
C-2. Disconnection of communication cable
C-3. Connector on the DC Controller PCB is disconnected.
Description
A. The communication with the Inserter or the Paper Folding Unit is interrupted.B. Failed communication for 3 consecutive times.
C. Failed communication for 3 consecutive times.
E505 -0001 -05 Title Finisher back-up RAM (EEPROM) error (Finisher-D1/E1)
Remedy The Finisher Controller PCB is faulty.Description The checksum for the EEPROM data has an error. (The valuewritten in EEPROM and the value extracted from EEPROM doesn't conform.)
E505 -0002 -05 Title EEPROM error (External 2 Hole Puncher)
Remedy The Punch Controller PCB is faulty.Description The checksum for the EEPROM data has an error.
E505 -0003 -05 Title A. EEPROM error with the Insertion Unit (failed data reading/
writing) (Document Insertion Unit-L1)
B. EEPROM error with the Insertion Unit (failed data reading/writing) (Document Insertion/Folding Unit-H1)
Remedy
A. The Insertion Unit Controller PCB is faulty.B. Folder Controller PCB is faulty.
Description
A. The checksum for the EEPROM data has an error.B. Data failed to be read properly.
E514 -8001 -05 Title Rear end assist home position error (Finisher-E1)
Remedy
1. The Rear End Assist Home Position Sensor (PI109) is faulty.2. The wiring between the Finisher Controller PCB and Rear End Assist Motor is faulty.
3. The end assist mechanism is faulty.
4. The Rear End Assist Motor (M109) is faulty.
5. The Finisher Controller PCB is faulty.
Description The stapler does not leave the rear end assist home positionwhen the Rear Eend Assist Motor has been driven for 3 seconds.
E514 -8002 -05 Title Rear end assist home position error (Finisher-E1)
Remedy
1. The Rear End Assist Home Pposition Sensor (PI109) is faulty.2. The wiring between the Finisher Controller PCB and Rear End Assist Motor is faulty.
3. The end assist mechanism is faulty.
4. The Rear End Assist Motor (M109) is faulty.
5. The Finisher Controller PCB is faulty.
Description The stapler does not return to the rear end assist homeposition when the Rear End Assist Motor has been driven for 3 seconds.
E518 -8001 -05 Title Error in Folding Feed Motor lock (Document Insertion/Folding Unit-H1)
Remedy
1. Connector of the Folding Feed Motor (M5) is disconnected.2. Folding Feed Motor (M5) is faulty.
Description The Folding Feed Motor (M5) lock signal has been detected
for more than the specified time.
E519 -0002 -05 Title Gear change home position error (Finisher-E1)
Remedy
1. The Gear Change Home Position Sensor (PI117) is faulty.2. The wiring between the Finisher Controller PCB and Gear Change Motor is faulty.
3. The gear change mechanism is faulty.
4. The Gear Change Motor (M110) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Gear Change Hhome Position Sensor does not turn ONwhen the Gear Change Motor has been driven for 387 pulses.
E519 -8001 -05 Title Gear change home position error (Finisher-E1)
Remedy
1. The Gear Change Home Position Sensor (PI117) is faulty.2. The wiring between the Finisher Controller PCB and Gear Change Motor is faulty.
3. The gear change mechanism is faulty.
4. The Gear Change Motor (M110) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Gear Change Home Position Sensor does not turn OFFwhen the Gear Change Motor has been driven for 387 pulses.
E530 -8001 -05 Title Front aligning plate home position error (Finisher-E1)
Remedy
1. The Front Aligning Plate Home Position Sensor (PI106) is faulty.2. The wiring between the Finisher Controller PCB and Front Aligning Plate Motor is faulty.
3. The front aligning plate is faulty.
4. The Front Aligning Plate Motor (M103) is faulty.
5. The Finisher Controller PCB is faulty.
DescriptionThe aligning plate does not leave the Aligning Plate FrontHome Position Sensor when the Alignment Plate Front Motor has been driven for 4 seconds.
E530 -8002 -05 Title Front aligning plate home position error (Finisher-E1)
Remedy
1. The front Aligning Plate Home Position Sensor (PI106) is faulty.2. The wiring between the Finisher Controller PCB and front aligning plate Motor is faulty.
3. The front aligning plate is faulty.
4. The front aligning plate Motor (M103) is faulty.
5. The Finisher Controller PCB is faulty.
Description The aligning plate does not return to aligning plate front homeposition Sensor when the alignment plate front Motor has been driven for 4 seconds.
E531 -8001 -05 Title Staple home position error (Finisher-E1)
Remedy
1. The wiring between the Finisher Controller PCB and Stapler is faulty.2. The Stapler is faulty.
3. The Finisher Controller PCB is faulty.
Description The Stapler does not leave the staple home position whenthe Staple Motor has been driven for 0.4 sec.
E531 -8002 -05 Title Staple home position error (Finisher-E1)
Remedy
1. The wiring between the Finisher Controller PCB and Stapler is faulty.2. The Stapler is faulty.
3. The Finisher Controller PCB is faulty.
Description The Stapler does not return to the staple home position whenthe Staple Motor has been driven for 0.4 sec.
E532 -8001 -05 Title Stapler shift home position error (Finisher-E1)
Remedy
1. The Stapler Drive Home Position Sensor (PI110) is faulty.2. The wiring between the Finisher Controller PCB and Stapler Shift Motor is faulty.
3. The stapler shift base is faulty.
4. The Stapler Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
DescriptionThe Stapler does not leave the stapler shift home pposition
when the Stapler Shift Motor hasbeen driven for 5 seconds.
E532 -8002 -05 Title Stapler shift home position error (Finisher-E1)
Remedy
1. The Stapler Drive Home Position Sensor (PI110) is faulty.2. The wiring between the Finisher Controller PCB and Stapler Shift Motor is faulty.
3. The stapler shift base is faulty.
4. The Stapler Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
DescriptionStapler does not return to the stapler shift home positionwhen the Stapler Shift Motor has been driven for 20 seconds.
E535 -8001 -05 Title Swing home position error (Finisher-E1)
Remedy
1. The Swing Home Position Sensor (PI105) is faulty.2. The wiring between the Finisher Controller PCB and Swing Motor is faulty.
3. The swing mechanism is faulty.
4. The Swing Motor (M106) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Stapler does not leave the swing home position when theSwing Motor has been driven for 3 seconds.
E535 -8002 -05 Title Swing home position error (Finisher-E1)
Remedy
1. The Swing Home Position Sensor (PI105) is faulty.2. The wiring between the Finisher Controller PCB and Swing Motor is faulty.
3. The swing mechanism is faulty.
4. The Swing Motor (M106) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Stapler does not return to the swing home position whenthe Swing Motor has bee driven for 3 seconds.
E537 -8001 -05 Title Rear aligning plate home position error (Finisher-E1)
Remedy
1. The Aligning Plate Rear Home Position Sensor (PI107) is faulty.2. The wiring between the Finisher Controller PCB and Aligning Plate Rear Motor is faulty.
3. The rear aligning plate is faulty.4. The Rear Aligning Plate Motor (M104) is faulty.
5. The Finisher Controller PCB is faulty.
Description The aligning plate does not leave the Aligning Plate RearHome Position Sensor when the Alignment Plate Rear Motor has been driven for 4 seconds.
E537 -8002 -05 Title Rear aligning plate home position error (Finisher-E1)
Remedy
1. The Aligning Plate Rear Home Position Sensor (PI107) is faulty.2. The wiring between the Finisher Controller PCB and Aligning Plate Rear Motor is faulty.
3. The rear aligning plate is faulty.
4. The Rear Aligning Plate Motor (M104) is faulty.
5. The Finisher Controller PCB is faulty.
Description The aligning plate does not return to Aligning Plate RearHome Position Sensor when the Alignment Plate Rear Motor has been driven for 4 seconds.
E540 -8001 -05 Title Tray 1 time out error (Finisher-E1)
Remedy
1. The Tray 1 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description
1. If the tray does not return to home position when the Tray 1 Shift Motor is driven for 25 seconds.
2. If the tray does not move to other area when Tray 1 Shift Motor is driven for 5 seconds.
E540 -8002 -05 Title Tray 1 shift area error (Finisher-E1)
Remedy
1. The Tray 1 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description
1. The dangerous area is reached before the Tray 1 PaperSurface Sensor detects paper surface during the paper surface detection operation.
2. A discontinuous area is detected during tray operation.
E540 -8003 -05 Title Swing Guide Switch/Staple Safety Switch error (Finisher-E1)
Remedy
1. The Tray 1 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description The swing guide switch or staple safety switch is activatedwhile the tray is operating.
E540 -8004 -05 Title The Tray 1 Shift Motor clock error (Finisher-E1)
Remedy
1. The Tray 1 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description The FG input cannot be detected when the Tray 1 Shift Motorhas been driven for 0.2 second.
E540 -8005 -05 Title The Tray 1 Shift Motor speed error (Finisher-E1)
Remedy
1. The Tray 1 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description The lock detection signal turns OFF 150 msec after the lockdetection signal turned ON.
E540 -8006 -05 Title The Tray 1 Shift Motor acceleration error (Finisher-E1)
Remedy
1. The Tray 1 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description
The lock detection signal does not turn ON when the Tray 1Shift Motor has been driven for 1 second.
E540 -8007 -05 Title The Tray 1 Shift Motor error (Finisher-E1)
Remedy
1. The Tray 1 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 1 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description
The lock detection signal does not turn OFF when the Tray 1 Shift Motor is at a stop.
E542 -8001 -05 Title Tray 1 time out error (Finisher-E1)
Remedy
1. The Tray 2 shift area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.4. The Tray 2 shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
Description
1. If the tray does not return to home position when the Tray 1Shift Motor is driven for 25 seconds.
2. If the tray does not move to other area when Tray 2 Shift Motor is driven for 5 seconds.
E542 -8002 -05 Title Tray 2 shift area error (Finisher-E1)
Remedy
1. The Tray 2 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 2 Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
Description
1. The upper limit area is reached before the Tray 2 PaperSurface Sensor 1 detects the paper surface during paper surface detection operation.
2. A discontinuous area is detected during tray operation.
3. During evacuation operation, arrival at the area beyond
the Tray 2 Paper Surface Sensor 2 is detected before this Sensor detects paper surface.
E542 -8004 -05 Title The Tray 2 Shift Motor clock error (Finisher-E1)
Remedy
1. The Tray 2 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 2 Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
DescriptionThe FG input cannot be detected when the Tray 2 Shift Motorhas been driven for 0.2 second.
E542 -8005 -05 Title The Tray 2 Shift Motor speed error (Finisher-E1)
Remedy
1. The Tray 2 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 2 Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
Description The lock detection signal turns OFF 150 msec after the lock detection signal turned ON.
E542 -8006 -05 Title The Tray 2 Shift Motor acceleration error (Finisher-E1)
Remedy
1. The Tray 2 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 2 Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
Description The lock detection signal does not turn ON when the Tray 2Shift Motor has been driven for 1 second.
E542 -8007 -05 Title The Tray 2 Shift Motor error (Finisher-E1)
Remedy
1. The Tray 2 Shift Area Sensor PCB is faulty.2. The wiring between the Finisher Controller PCB and Tray 2 Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 2 Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
Description The lock detection signal does not turn OFF when the Tray 2Shift Motor is at a stop.
Thousands of Parts and Free Shipping
No comments:
Post a Comment