Thousands of Parts and Free Shipping
Errorcode E012 To E020 for Canon ImageRunner Advance 6275 6265 6255
.
E012 -0001 -05 Title Drum Motor (M1) error
Detection description
Lock error of the Drum Motor (M1).
Remedy 1. Check the connection of the Main Driver PCB (PCB2) and
the Drum Motor (M1).Motor side: J2138, PCB side: J109
2. Check the voltage of the Drum Motor (M1) J2151.
If voltage is 0V, check the connection of the Relay PCBJ520.
3. Replace the Drum Motor (M1).
4. Check the gear of the Drum Drive Shaft.
If the load is too much, replace the Process Unit and the Drum Drive Unit (Shaft).
5. Replace the Main Driver PCB (PCB2).
6. Replace the DC Controller PCB (PCB1).
E013-0001 -05 Title Error in Waste Toner Lock Detection Connector disconnection
Detection description
The Waste Toner Lock Detection Switch (SW5) detects locked
state 3 times for 200 msec at power-on.
Remedy Check the connection of the Waste Toner Lock Detection
Switch (SW5) and the Main Driver PCB (PCB2).
Switch side: J3050, PCB side: J103
E013-0002 -05 Title Error in Waste Toner Feed Screw Lock detection
Detection description
The Waste Toner Lock Detection Switch detects locked state 3
times for 200 msec while the Developing Assembly is driven.
Remedy 1. Check the Waste Toner Container and the Waste Toner Container Pipe.
If toner overflowed from the Waste Toner Container clogs
the outlet of the Waste Toner Pipe, remove the clogged toner.
After removing it, check that the screw can be seen from
the outlet of the pipe.
2. Check the connection of the Waste Toner Lock Detection
Switch (SW5) and the Main Driver PCB (PCB2).
3. Check the connection of the Main Driver PCB (PCB2) and
the DC Controller PCB (PCB1).
Main Controller side: J3050, DC Controller side: J103
4. Replace the Waste Toner Lock Detection Switch (SW5).
5. Replace the Waste Toner Feed Unit.
6. Replace the Main Driver PCB (PCB2).
7. Replace the DC Controller PCB (PCB1). (When the error
is still displayed after replacing the Waste Toner Feed Unit
and the Main Driver PCB (PCB2).)
E014-0001 -05 Title Fixing Motor error
Detection description Lock error of the Fixing Motor (M3).
Remedy 1. Check the gear of the Fixing Drive Unit. -> Replace the gear.
2. Replace the Fixing Motor (M3).
3. Check the connection drawer between the Fixing Assembly and the host machine.
4. Replace the Main Driver PCB (PCB2).
E017-0001 -05 Title ETB disengagement error
Detection description
Disengagement of the ETB is not completed within the
specified period of time.
Remedy 1. Check the connection of the ETB Disengage Sensor (PS56).
Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver PCB (PCB4))
2. Check the connection of the Duplex Feed Left Motor (M19).
Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4))
3. Replace the ETB Disengage Sensor (PS56).
4. Replace the Duplex Feed Left Motor (M19).
5. Replace the Duplex Driver PCB (PCB4).
6. Replace the DC Controller PCB (PCB1).
NOTE:
Check if the Disengagement Cam is stained. If necessary, clean it.
Check if the drive system (gear, Motor, one-way) is failed. If necessary, replace it.
Check if the link with the Fixing Feed Handle is failed. If necessary, replace it.
E017-0002 -05 Title ETB engagement error
Detection description
Engagement of the ETB is not completed within the specified period of time.
Remedy 1. Check the connection of the ETB Disengage Sensor (PS55).
Sensor side: J2100, J3270, PCB side: J343 (Duplex Driver PCB (PCB4))
2. Check the connection of the Duplex Feed Left Motor (M19).
Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4))
3. Replace the ETB Engage Sensor (PS55).
4. Replace the Duplex Feed Left Motor (M19).
5. Replace the Duplex Driver PCB (PCB4).
6. Replace the DC Controller PCB (PCB1).
NOTE:
Check if the Disengagement Cam is stained. If necessary, clean it.
Check if the drive system (gear, Motor, one-way) is failed. If
necessary, replace it.
Check if the link with the Fixing Feed Handle is failed. If necessary, replace it.
E017-0003 -05 Title ETB HP error
Detection description
Engagement of the ETB was not completed at initialization.
Remedy If this error occurs at installation, the ETB Disengage Member
(Transfer Frame Stopper) may be left unremoved. Refer
to the troubleshooting "Remedy to be implemented when
the ETB Disengage Member (Transfer Frame Stopper) is
left unremoved" in the Service Manual, and check whether
the ETB Disengage Member is left unremoved or not and
implement appropriate procedure.
If this error occurs at times other than installation, follow the
following steps to implement check and remedy.
1. Check the connection of the ETB Disengage Sensor (PS56).
Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver PCB (PCB4))
2. Check the connection of the Duplex Feed Left Motor (M19).
Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4))
3. Replace the ETB Disengage Sensor (PS56).
4. Replace the Duplex Feed Left Motor (M19).
5. Replace the Duplex Driver PCB (PCB4).
6. Replace the DC Controller PCB (PCB1).
NOTE:
Check if the Disengagement Cam is stained. If necessary, clean it.
Check if the drive system (gear, Motor, one-way) is failed. If necessary, replace it.
Check if the link with the Fixing Feed Handle is failed. If necessary, replace it.
E020-000 -05 Title Developing Assembly toner absent error
Detection description
Toner in the Developing Assembly was empty for 2 minutes.
Remedy 1. Check the connection of the Developing Toner Sensor (TS1).
Sensor side: J2133, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2))
2. Check the connection of the Magnet Roller Clutch (CL5).
Sensor side: J2036, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
3. Check the connection of the Toner Feed Motor (M28).
Motor side: J2035, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
4. Check the connection of the Buffer Toner Sensor (TS3).
Sensor side: J2039, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
5. Replace the Developing Toner Sensor (TS1).
6. Replace the Magnet Roller Clutch (CL5).
7. Replace the Toner Feed Motor (M28).
8. Replace the Buffer Toner Sensor (TS3).
9. Replace the Main Driver PCB (PCB2).
10. Replace the DC Controller PCB (PCB1).
E020-0001 -05 Title Error in Developing Toner Sensor connection detection
Detection description
The connection detection port was OFF at power-on.
Remedy 1. Check the connection of the Developing Toner Sensor (TS1).
Sensor side: J2133, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2))
2. Replace the Developing Toner Sensor (TS1).
3. Replace the Main Driver PCB (PCB2).
4. Replace the DC Controller PCB (PCB1).
E020-0002 -05 Title Error in Buffer Toner Sensor connection detection
Detection description
The connection detection port was OFF at power-on.
Remedy 1. Check the connection of the Buffer Toner Sensor (TS3).
Sensor side: J2039, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
2. Replace the Buffer Toner Sensor (TS3).
3. Replace the Main Driver PCB (PCB2).
4. Replace the DC Controller PCB (PCB1).
E020-0003 -05 Title Error in the Toner Excess Supply Sensor connection detection
Detection description
The connection detection port was OFF at power-on.
Remedy 1. Check the connection of the Toner Excess Supply Sensor (TS2).
Sensor side: J2038, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
2. Replace the Toner Excess Supply Sensor (TS2).
3. Replace the Main Driver PCB (PCB2).
4. Replace the DC Controller PCB (PCB1).
E020-0004 -05 Title Error in Magnet Roller Clutch connection detection
Detection description
The connection detection port was OFF at power-on.
Remedy 1. Check the connection of the Magnet Roller Clutch (CL5).
Sensor side: J2036, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
2. Replace the Magnet Roller Clutch (CL5).
3. Replace the Main Driver PCB (PCB2).
4. Replace the DC Controller PCB (PCB1).
E020-0020 -05 Title Error in Developing Assembly Toner Sensor Cleaning Scraper displacement
Detection description State without toner was detected continuously.
Remedy 1. Turn OFF the main power.
2. Replace the Developing Assembly.
3. Turn ON the main power.
E020-0021 -05 Title Error in Developing Assembly Toner Sensor Cleaning Scraper displacement
Detection description State with toner was detected continuously.
Remedy 1. Turn OFF the main power.
2. Replace the Developing Assembly.
3. Turn ON the main power.
Thousands of Parts and Free Shipping
No comments:
Post a Comment