Canon ImageRunner 5570 6570 5570N 6570N, Errorcode E100 To E248 and Solution

E100 There is a BD error.

0001 A check is made of VLOCK at intervals of 100 msec while the laser is on. An error

will be identified if it is not detected 10 times in sequence.

- Replace the laser scanner unit. - Replace the DC controller PCB.

E110 There is a polygon motor error.

0001 - Although the polygon motor has been turned on, VLOCK is not detected at all within 76.5 sec.

- At time of a shift from full-speed to halfspeed control, VLOCK is not detected at all for 7.5 sec.

- At time of half-speed control, a check is made of VLOCK at intervals of 100 msec.

An error will be identified if it is not detected 10 times continuously.

- Replace the laser scanner unit.  - Replace the DC controller PCB.

E121 There is a controller cooling fan error.

0001 Even though the controller cooling fan has been turned on, the controller cooling fan

stop signal has been detected for 5 sec or more.

- Check the connector for any fault in connection. - Replace the fan.

E196 The EEPROM is faulty.

1abb There is a mismatch between the data that has been written in EEPROM and the data

that has been read. (a: chip No. 0 through 5; bb: chip faulty address)

- Initialize the RAM. - Replace the EEPROM. - Replace the DC controller PCB.

2abb The ID in EEPROM that has been read and the ID in ROM are compared. An error

will be identified if they do not match. (a: chip No. 0 through 5; bb: chip faulty address)

3abb When the main power is turned on, the ID in EEPROM and the ID in ROM are compared. An error will be identified if they do not match. (a: chip No. 0 through 5; bb: chip faulty address)

- Check the position and condition of the EEPROM.

- Initialize the RAM. - Replace the EEPROM.  - Replace the DC controller PCB.

E202 There is a scanner HP error.

0001 An error has occurred when the sensor was moved to home position. The scanner HP sensor is faulty; the scanner motor is faulty; the reader controller PCB is faulty.

- Check the connector for any fault in connection.  - Replace the scanner HP sensor.

- Replace the scanner motor. - Replace the reader controller PCB.

0002 An error has occurred when the sensor was moved from home position.

The scanner HP sensor is faulty; the scanner motor is faulty; the reader  controller PCB is faulty.

E225 The intensity of light is inadequate.

0001 At time of shading, the intensity if below a specific level.

- Check the connector for any fault in connection.  - Replace the scanning lamp.

- Replace the inverter PCB.    - Replace the reader controller PCB.

0002 ADFThe intensity is below a specific level  between sheets (ADF).

E227 there is an error in the power supply (24 V).

0001 At power-on, the 24-V port is OFF.

0002 At the start of a job, the 24-V port is OFF.

0003 At the end of a job, the 24-V port is off.

0004 When a load is driven, the 24-V port isOFF.

- Check the connector for any fault in connection.  - Replace the power supply.

E240 The communication between the main controller PCB and the DC controller PCB is faulty.

 0000 There is an error in the communication between the main controller PCB and the CPU of the DC controller PCB.

- Check the connector for any fault in connection.

- Replace the DC controller PCB.   - Replace the main controller PCB.

E248 There is an EEPROM error.

0001 An error has occurred at power-on.

0002 An error has occurred at time of writeoperation.

0003 An error has occurred at time of read  operation after write operation

- Replace the EEPROM.  - Replace the reader controller PCB.